Tubing design

Tubing design

In the previous chapter, selection procedure of tubing diameter was based on well performance analysis. In this section, the procedure for selecting tubing material properties is presented. Selection of material is carried out by considering different forces that act on the tubing during production and workover operations and then a graphical method is used to present the tubing load against material properties.

1.1 Forces on tubing

During the life of the well, tubing is subjected to various forces from production and workover operations which include:

Which Citation Styles Can You Handle?

We get a lot of “Can you do MLA or APA?”—and yes, we can! Our writers ace every style—APA, MLA, Turabian, you name it. Tell us your preference, and we’ll format it flawlessly.

* production of hydrocarbon,

* killing of the well,

* squeeze cementing,

* hydraulic fracturing etc.

Are Writing Services Legal?

Totally! They’re a legit resource for sample papers to guide your work. Use them to learn structure, boost skills, and ace your grades—ethical and within the rules.

The activities result in change in temperature and pressure inside the tubing and casing-tubing annulus, which can cause a change in tubing length (shortening or lengthening).

The change in length often leads to increase in compression or tension in tubing and in extreme situation unseating of packer or failure of tubing (Hammerlindl, 1977 and Lubinski et.al, 1962).

According to the authors the change in pressure inside and outside of tuning and temperature can have various effects on tubing:

* piston effect(According to Hooke’s Law),

What’s the Price for a Paper?

Starts at $10/page for undergrad, up to $21 for pro-level. Deadlines (3 hours to 14 days) and add-ons like VIP support adjust the cost. Discounts kick in at $500+—save more with big orders!

* helical buckling,

* ballooning and

* thermal effect.

HOOKE’S LAW EFFECT’S

Changes in pressure inside and outside the tubing can cause tubing movement due to piston effect. According to Hooke’s law, change in length of tubing caused by this effect can be calculated using the Equation 4.1.

Is My Privacy Protected?

100%! We encrypt everything—your details stay secret. Papers are custom, original, and yours alone, so no one will ever know you used us.

Where is the change in forces due to the change in pressures inside ( ) and outside () tubing and can be expressed as:

Where, (see Fig. 4.2)

DL1= change in length due to Hooke’s Law effect, inch,

L = length of tubing, inch,

Is AI Involved in Writing?

Nope—all human, all the time. Our writers are pros with real degrees, crafting unique papers with expertise AI can’t replicate, checked for originality.

F = force acting on bottom of tubing, lb.,

E= modulus of elasticity,

As = cross-sectional area of tubing, inch2,

Ai = area based on inside diameter of tubing, inch2 and

Why Are You the Best for Research?

Our writers are degree-holding pros who tackle any topic with skill. We ensure quality with top tools and offer revisions—perfect papers, even under pressure.

Ao = area based on outside diameter of tubing, inch2,

Ap= area based on diameter of packer seal, inch2,

= change in pressure inside annulus at packer (Final – Initial), psi and

= change in pressure inside tubing at packer (Final – Initial), psi.

Who Writes My Assignments?

Experts with degrees—many rocking Master’s or higher—who’ve crushed our rigorous tests in their fields and academic writing. They’re student-savvy pros, ready to nail your essay with precision, blending teamwork with you to match your vision perfectly. Whether it’s a tricky topic or a tight deadline, they’ve got the skills to make it shine.

Notes: DL, DF, DPi or DPo indicates change from initial packer setting conditions. It is assumed Pi = Po when packer is initially set.

HELICAL BUCKLING

The difference in pressure inside tubing and casing-tubing annulus acts on the cross sectional area of packer bore at tubing seal and leads to a decrease in the length of tubing due to buckling. This effect is known as helical buckling. When the tubing is restricted from movement, a tensile load is developed. This effect is increased with increase in inside tubing pressure.

The change in length caused by helical buckling can be calculated by the Equation 4.3.

where

Will My Paper Be Unique?

Guaranteed—100%! We write every piece from scratch—no AI, no copying—just fresh, well-researched work with proper citations, crafted by real experts. You can grab a plagiarism report to see it’s 95%+ original, giving you total peace of mind it’s one-of-a-kind and ready to impress.

Force causing buckling: Ff = Ap (Pi – Po)

If Ff (a fictitious force) is zero or negative, there is no buckling.

Length of tubing buckled: n = Ff / w

Where,

Can You Use Any Citation Format?

Yep—APA, Chicago, Harvard, MLA, Turabian, you name it! Our writers customize every detail to fit your assignment’s needs, ensuring it meets academic standards down to the last footnote or bibliography entry. They’re pros at making your paper look sharp and compliant, no matter the style guide.

DL2= change in length due to buckling, inch,

r= radial clearance between tubing and casing, inch,

w = ws + wi – wo,

ws = weight of tubing, lb/incn,

Can I Change My Order Details?

For sure—you’re not locked in! Chat with your writer anytime through our handy system to update instructions, tweak the focus, or toss in new specifics, and they’ll adjust on the fly, even if they’re mid-draft. It’s all about keeping your paper exactly how you want it, hassle-free.

wi =weight of fluid contained inside tubing, lb/in. (density multiplied by area based on ID of tubing),

wo= weight of annulus fluid displaced by bulk volume of tubing, lb/in. (density multiplied by area based on OD of tubing),

=tubing outside diameter, inch and

=tubing inside diameter, inch.

How Do I Order a Paper?

It’s a breeze—submit your order online with a few clicks, then track progress with drafts as your writer brings it to life. Once it’s ready, download it from your account, review it, and release payment only when you’re totally satisfied—easy, affordable help whenever you need it. Plus, you can reach out to support 24/7 if you’ve got questions along the way!

Buckling can be avoided by applying surface annular pressure.

BALLOONING EFFECT’S

The radial pressure inside the tubing causes tubing to increase or decrease in length. When the pressure inside the tubing is greater compared to the pressure inside the casing-tubing annulus, it tends to inflate the tubing, thus shortening the tubing. If the pressure inside the casing-tubing annulus is greater compared to pressure inside the tubing, then the tubing length is increased. This effect is known as ballooning and the change in length caused due to this effect is given by Equation 4.4.

Where,

DL3=change in length due to ballooning, in.

How Quick Can You Write?

Need it fast? We can whip up a top-quality paper in 24 hours—fully researched and polished, no corners cut. Just pick your deadline when you order, and we’ll hustle to make it happen, even for those nail-biting, last-minute turnarounds you didn’t see coming.

m= Poisson’s ratio (0.3 for steel)

R= tubing OD/tubing ID

Dri=change in density of fluid inside tubing, lb/in3

Dro=change in density of fluid outside tubing, lb/ in3

Dpi=change in surface pressure inside tubing, psi

Can You Handle Tough Topics?

Absolutely—bring it on! Our writers, many with advanced degrees like Master’s or PhDs, thrive on challenges and dive deep into any subject, from obscure history to cutting-edge science. They’ll craft a standout paper with thorough research and clear writing, tailored to wow your professor.

Dpo=change in surface pressure outside tubing, psi

d=pressure drop in tubing due to flow, psi/in. (usually considered as d= 0)

THERMAL EFFECT’S

Due to the earth’s geothermal gradient, the temperature of the produced fluids can be high enough to change the tubing length. The effect is opposite (decrease in length) when a cold fluid is injected inside the tubing. It is ideal to take the change in average string temperature. The change in length due to temperature can be calculated using the Equation 4.5.

Where,

DL4=change in length, in.

How Do You Match Professor Expectations?

We follow your rubric to a T—structure, evidence, tone. Editors refine it, ensuring it’s polished and ready to impress your prof.

L=length of tubing string, in.

C=coefficient of expansion of steel per oF

DT=temperature change, oF

PACKER SETTING FORCE

How Do You Edit My Work?

Send us your draft and goals—our editors enhance clarity, fix errors, and keep your style. You’ll get a pro-level paper fast.

The setting of packer requires forces which may lead to change in length of tubing.

This change in length can be calculated using the Equation 4.6., which is derived based on Equations 4.1 and 4.3.

The force on packer should not exceed critical values whereby it can cause permanent damage to the tubing. The initial weight on packer may cause “slack off” and to check if this situation might exist, one could use Equation 4.7.

Where, F = set-down force.

The tubing can suffer permanent damage if the stress in the tubing exceeds the yield strength of the tubing material. It is therefore advised to determine the safe tubing stresses for a given production or workover operation. The safe tubing stress can be calculated by using the following Equations (Allen and Roberts, 1989):

Can You Brainstorm Topics?

Yep! We’ll suggest ideas tailored to your field—engaging and manageable. Pick one, and we’ll build it into a killer paper.

The critical values can be calculated using Equations 4.8 and 4.9.

Where,

Si=stress at inner wall of the tubing

So=stress at outer wall of the tubing

For free-motion packer:

When the packer exerts some force on the tubing, an additional term Ff should be added to Fa and the sign in Equations 4.8 and 4.9 varies in way to maximize the stresses.

Example 4.1: An example of Tubing Movement calculation:

The following operations are to be performed on a well completed with 9,000 ft of 2-7/8″ OD (2.441″ ID), 6.5 lb/ft tubing. The tubing is sealed with a packer which permits free motion. The packer bore is 3.25″. The casing is 32 lb/ft, 7″ OD (6.049″ ID). Calculate the total movement of the tubing (note: ” notation is used for inch).

Conditions Do You Offer Fast Edits? Yes! Need a quick fix? Our editors can polish your paper in hours—perfect for tight deadlines and top grades.	Production	Frac	Cement
Initial Fluid	12 lb/gal mud	13 lb/gal saltwater Can You Start With an Outline? Sure! We’ll sketch an outline for your approval first, ensuring the paper’s direction is spot-on before we write.	8.5 lb/gal oil
Final Fluid
Tubing	10 lb/gal oil	11 lb/gal frac fluid	15 lb/gal cement
Annulus	12 lb/gal mud Can You Add Charts or Stats? Definitely! Our writers can include data analysis or visuals—charts, graphs—making your paper sharp and evidence-rich.	13 lb/gal saltwater	8.5 lb/gal oil
Final Pressure
Tubing	1500 psi	3500 psi	5000 psi
Annulus	0	1000 psi What About Multi-Part Projects? We’ve got it—each section delivered on time, cohesive and high-quality. We’ll manage the whole journey for you.	1000 psi
Temp Change	+25oF	-55oF	-25oF Do You Adapt to International Rules? Yes! UK, US, or Aussie standards—we’ll tailor your paper to fit your school’s norms perfectly.

SOLUTION

Production:

Hooke’s Law Effect

At bottom hole conditions

DPi = Final pressure inside tubing – Initial pressure inside tubing

DPo = Final pressure inside annulus – initial pressure inside annulus

Using Eq. (4.2)

Using Eq. (4.1)

What does a complex assignment mean?

If your assignment needs a writer with some niche know-how, we call it complex. For these, we tap into our pool of narrow-field specialists, who charge a bit more than our standard writers. That means we might add up to 20% to your original order price. Subjects like finance, architecture, engineering, IT, chemistry, physics, and a few others fall into this bucket—you’ll see a little note about it under the discipline field when you’re filling out the form. If you pick “Other” as your discipline, our support team will take a look too. If they think it’s tricky, that same 20% bump might apply. We’ll keep you in the loop either way!

Helical Buckling Effect

Using Eq. (4.3)

Ballooning Effect

Using Eq. (4.4)

Temperature Effect

Using Eq. (4.5)

Total Tubing Movement

Who is my writer? How can I communicate with him/her?

Our writers come from all corners of the globe, and we’re picky about who we bring on board. They’ve passed tough tests in English and their subject areas, and we’ve checked their IDs to confirm they’ve got a master’s or PhD. Plus, we run training sessions on formatting and academic writing to keep their skills sharp. You’ll get to chat with your writer through a handy messenger on your personal order page. We’ll shoot you an email when new messages pop up, but it’s a good idea to swing by your page now and then so you don’t miss anything important from them.

(Tubing lengthens)

Fracturing:

Hooke’s Law Effect

At bottom hole conditions

DPi = Final pressure inside tubing – Initial pressure inside tubing

DPo = Final pressure inside annulus – initial pressure inside annulus

Using Eq. (4.2)

Using Eq. (4.1)

Helical Buckling Effect

Using Eq. (4.3)

Ballooning Effect

Using Eq. (4.4)

Temperature Effect

Using Eq. (4.5)

Total Tubing Movement

(Tubing shortens)

Cement:

Hooke’s Law Effect

At bottom hole conditions

DPi = Final pressure inside tubing – Initial pressure inside tubing

DPo = Final pressure inside annulus – initial pressure inside annulus

Using Eq. (4.2)

Using Eq. (4.1)

Helical Buckling Effect

Using Eq. (4.3)

Ballooning Effect

Using Eq. (4.4)

Temperature Effect

Using Eq. (4.5)

Total Tubing Movement

(Tubing shortens)

1.2 Selection of Tubing Material

Tubing selection should be based on whether or not the tubing can withstand various forces which are caused due to the variations in temperature and pressure. The API has specified tubing based on the steel grade. Most common grades are: H40, J55, K55, C75, L80, N80, C95, P105 and P110. The number following the letter indicates the maximum yield strength of the material in thousands of psi. The failure of the tubing can be attributed to the loading conditions. There are three modes of tubing failure which include:

* burst (pressure due to fluid inside tubing),

* collapse (pressure due to fluid outside tubing) and

* tension (due to weight of tubing and tension if restricted from movement).

The graphical design of the tubing can be achieved by creating a plot of depth vs pressure. This design is carried out by calculating pressures inside the tubing and casing-tubing annulus at the bottom hole and tubing head. The maximum differential pressures at surface and bottom hole are examined using the plot. This maximum condition usually occurs during stimulation.

When the maximum allowable annular pressure is maintained during stimulation, a considerable amount of reduction in the tubing load can be achieved. The burst pressure load (difference between the pressure inside the tubing and annulus) is mostly experienced in greater magnitude close to the surface but may not necessarily be always true. The burst load lines are plotted followed by plotting collapse load lines.

The collapse loads are calculated with an assumption that a slow leak at the bottom hole has depressurized the tubing. This scenario is sometimes expereinced after the fracturing treatment when operators commence kickoff before bleeding off the annular pressure.

If the data for pressure testing conditions (usually most critical load) is available, it should be included in the plot.

Along with the collapse and burst loads, the burst and collapse resistance for different tubing grades (available) are plotted. By observing the plot we can determine which tubing grade to be selected that can withstand the calculated loads.

An example of selecting tubing based on graphical design is presented below.

Example 4.2: Graphical tubing design

Based on the data given below, select a tubing string that will satisfy burst, collapse and tension with safety factors of 1.1, 1.0 and 1.8 respectively.

Planning Data:

D =9000 ft true depth,

f = 2.875 inches, tubing OD,

CIBHP = 6280psi, closed-in bottom hole pressure,

FBP = 12550psi, formation breakdown pressure,

FPP = 9100psi, fracture propagation pressure,

Gpf = 0.4 psi / ft packer fluid gradient,

Gf = .48 psi /ft fracturing fluid gradient,

g = 0.75 gas gravity at reservoir,

Pann = 1000 psi, maximum allowable annulus pressure,

SFB =1.1, safety Factor, Burst Condition,

SFC =1.0, safety Factor, Collapse Condition,

SFT =1.8, safety Factor, Tensile Load,

Burst and Collapse rating of available tubing’s:

B_L80 =9395 psi,

C_L80 =9920 psi,

B_J55 =6453 psi,

C_J55 =6826 psi,

B_H40 =4693 psi and

C_H40 =4960psi.

Solution:

Step 1: Calculate the ratio of bottomhole pressure to surface pressure.

Referring table 4.1 in the manual, determine the ratio of surface and BHP at the given reservoir gas gravity,

At a gas gravity = 0.8 and Depth 9000 ft, the ratio is 0.779

At a gas gravity = 0.7 and Depth 9000 ft, the ratio is 0.804

At gas gravity 0.75 the ratio of surface pressure to BHP is

Table 4.1 – Ratio of surface pressure and BHP in gas wells for a range of gas gravities.

Depth of Hole		Gas Gravity
(ft)	(m)	0.60	0.65	0.70	0.80
1000	305	0.979	0.978	0.976	0.973
2000	610	0.959	0.956	0.953	0.946
3000	915	0.939	0.935	0.93	0.92
4000	1219	0.92	0.914	0.907	0.895
5000	1524	0.901	0.893	0.885	0.87
6000	1830	0.883	0.873	0.854	0.847
7000	2133	0.864	0.854	0.844	0.823
8000	2438	0.847	0.835	0.823	0.801
9000	2743	0.829	0.816	0.804	0.779
10000	3048	0.812	0.798	0.764	0.758
11000	3353	0.795	0.78	0.766	0.737
12000	3660	0.779	0.763	0.747	0.717
13000	3962	0.763	0.746	0.729	0.697
14000	4267	0.747	0.729	0.712	0.678
15000	4572	0.732	0.713	0.695	0.659
16000	4876	0.717	0.697	0.67	0.641
17000	5181	0.702	0.682	0.652	0.624
18000	5486	0.687	0.656	0.645	0.607
19000	5791	0.673	0.652	0.631	0.59
20000	6097	0.659	0.637	0.615	0.574

Step 2: Calculate the pertinent pressures for different operating conditions.

a) Pressures inside casing-tubing annulus

Assuming during the production and killing of well, packer fluid is present inside the casing tubing annulus.

For producing situation:

Pressure inside annulus at surface = packer fluid gradient * Depth

Pkill_prod_surface= = 0.4* 0 = 0 psi

Pressure inside annulus at bottom hole = packer fluid gradient * Depth

Pkill_prod = Gpf *D = 0.4* 9000 = 3600 psi

For Stimulation:

Pressure inside annulus at surface= Pstim_surf = 1000 psi

Pressure inside annulus at bottomhole = packer fluid gradient * Depth + (Max

Allowable pressure inside annulus)

Pstim_bh= Gpf *D + Pann = 0.4*9000 + 1000 = 4600 psi

b) Pressures inside tubing

At bottom hole, pressure = CIBHP

At surface, pressure = CITHP (closed in tubing head pressure)

CITHP = ratio * CIBHP

CITHP = 0.792 * 6280 = 4973 psi

KILL SITUATION:

When a well is killed, the bottom hole pressure is given as sum of CIBHP and maximum allowable annulus pressure.

At bottom hole, pressure inside tubing during kill situation (BHIP) = CIBHP+Pann

BHIP =6280 +1000 = 7280psi

Tubing head pressure during kill situation is calculated by multiplying BHIP with gas gravity.

At tubing head kill pressure (THIP) = ratio * BHIP = 0.792*7280 = 5765 psi

FORMATION BREAKDOWN SITUATION:

During stimulation the bottomhole pressure is the formation break down pressure and can be calculated by the density of the fracture fluid .In this problem the break down pressure is specified.

At bottomhole, pressure inside tubing during formation breakdown (BHFBP) = FBP

BHFBP = 12550 psi

The tubing head pressure can be calculated by subtracting the hydrostatic head generated by the fracturing fluid from the bottomhole pressure.

At tubing head, pressure (THFBP) = FBP -Gf* D

=12550- 0.48* 9000 = 8230psi

FRACTURE PROPAGATION

During stimulation (propagation), we experience some pressure drop due to friction. Based on the pumping rates and properties of proppants we can determine the drop in pressure. Assuming a pressure drop of 0.35 psi / ft (usually calculated through properties of fracturing fluid and pumping rate), the bottomhole pressure at fracture propagation (BHFP) can be calculated as:

DPfr = 0.35 psi/ ft

At bottomhole, BHFP = FPP

BHFP =9100 psi

At tubing head, the pressure inside tubing can be calculated as:

Tubing head fracture propagation pressure (THFP) = BHFP + DPfr* D – Gf*D

= 9100 + 0.35*9000 -0.48*9000 =7930 psi

Step 3: Calculate the burst load for different operating conditions:

Defining the burst loads:

Burst Load pressure = pressure inside tubing – pressure in the casing- tubing annulus

Burst Load at tubing head for producing conditions:

BL _surface_prod = CITHP – Pkill_prod_surface = 4973 – 0 = 4973 psi

Burst Load at bottomhole for producing conditions:

BL _bh_prod = CIBHP – Pkill_prod = 6280-3600 = 2680 psi

Burst Load at tubing head for killing operation:

BL _surface_kill = THIP – Pkill_prod_surface = 5765 -0 = 5765 psi

Burst Load at bottomhole for killing operation:

BL _bh_kill = BHIP – Pkill_prod = 7280-3600 = 3680 psi

Burst Load at tubing head for formation breakdown:

BL _surface_fbp = THFBP – Pstim_surf = 8230 -1000 = 7230 psi

Burst Load at bottomhole for formation breakdown:

BL _bh_fbp = BHFBP – Pstim_bh = 12550 -4600 = 7950 psi

Burst Load at tubing head for fracture propagation:

BL _surface_fbp = THFP – Pstim_surf = 7930 -1000 = 6930 psi

Burst Load at bottomhole for fracture propagation:

BL _bh_fbp = BHFP – Pstim_bh = 9100 -4600 = 4500 psi

Step 4: Calculation of collapse Load

Defining the collapse loads:

Collapse load pressure = pressure in casing-tubing annulus- pressure inside tubing

In order to plot critical collapse load conditions (CLL) normally, we assume that a slow leak in tubing has changed the pressure inside casing-tubing annulus to CITHP and that tubing is empty and depressurized.

Step 5: Plot the Load lines.

Plot the burst load and collapse load lines for various completion operations, burst and collapse resistance lines for the available tubing grades. The obtained plot is illustrated in Fig. 4.4.

It can be observed from plot that formation breakdown situation has the maximum burst pressures. The maximum burst pressure line and collapse line are plotted with the available ratings of tubing. The resulting plot will look like Fig. 4.5.

Then by inspecting the graph we can come to a conclusion that L-80 grade is the best grade available that can withstand the collapse and burst pressures during various operations. But in other situations we have an option to select multiple grades on tubing which are guided by the estimated loading conditions.

Estimation of Tensile Load:

Most of the tubing failures are caused due to coupling leakage and failure. The failure of coupling can be attributed to inadequate design for tension of the tubing.

This load being one of the significant and causes most failures compared to failures due to burst and collapse pressures.

A higher safety factor is used while designing tubing. The design can be initiated by considering only the weight of tubing on packer. Some companies even ignore buoyancy effects while calculating weight to have a better design.

So ideally a tubing design for tension is carried out by calculating the weight of the tubing in air. Then the buoyant weight of the tubing is calculated using the densities of steel and mud. Selecting a grade of casing which can handle the tensile load generated due to the weight of the tubing. An example below illustrates the design of tubing for tension.

Example 4.3

Tension Design

Tubing weight: 7.2 lb/ft

Tubing length: 12,500 ft

Packer fluid: 0.38 psi/ft = 54.72 lb/ft3

Density of steel: 490 lb/ft3

Win_air = 7.2 x 12,500 = 90,000 lb

Wbuoyant = = 0.89 x 73,600 = 80,100 lb

Joint Specifications

	J55		L80
	EUE	HYD CS		EUE	HYD A95
API joint strength (Klb) Design factor Design capacity (Klb)	99.7 1.8 55.4	100 1.8 55.6		135.9 1.8 75.5	150 1.8 83.3

Tubing Tension Design Considerations

1. Requires L80 tubing at surface

2. Requires joint strength capability of HYD A95 or equivalent

Review questions

1. When would buckling of tubing above a packer likely to occur?

2. A 10,000-ft, high-rate oil well is completed with 5½” 15.5 lb/ft tubing (wall thickness 0.275″). Under producing conditions the flowing temperature gradient is 0.40F/100 ft, and under static conditions the geothermal gradient is 1.8oF/100ft from a mean surface temperature of 40oF. When the well is killed with a large volume of 40oF seawater, the bottom-hole temperature drops to 70oF. If free to move, what tubing movement can be expected from the landing condition to the hot producing and to the cold injection conditions? If a hydraulic packer were to be used and set in 30,000 lb tension, what would be the tension loading on the packer after killing the well? (Ignore piston, ballooning and buckling effects).

3. A 7000-ft well that is to be produced with a target of 15,000 STB/D using 5½” tubing encounters 170 ft of oil-bearing formation with a pressure of 3000 psi. What rating of wellhead should be used? If a single grade and weight tubing is to be used, what is the cheapest string that can probably be run, assuming that

Grade	Weight (lb/ft)	Collapse Strength (psi)	Burst Strength (psi)	Tensional Strength (1000 lb)	Cost Comparison
J-55 C-75 N-80	15.5 17.0 17.0 17.0 20.0	4040 4910 6070 6280 8830	4810 5320 7250 7740 8990	300 329 423 446 524	Cheapest Most expensive Moderately expensive

REFERENCES

1. Allen, TO and Roberts, AP, Well Completion Design- Production Operations-1, 3rd edition, 1989, pp 182-187.

1. Hammerlindl, DT, Movement, Forces and Stress Associated with Combination Tubing Strings Sealed with Packers, JPT, February 1977.

2. Lubinski, A, Althouse, WS, Logan, TL, Helical Buckling of Tubing Sealed in Packers, JPT, June 1962.

3. Well completion design and practices PE 301-IHRDC E&P Manual Series, Boston, MA 02116, USA.

Tags: Assignment Help: USA's #1 Online Assignment Writing Service, Assignments for you - Online Assignment Maker - Writing Services, Best Online Classes Hub, Online Homework Help: Do My Online Class Assignment